GTO Pedders Track 2 Package

Coilovers - * Required

1 x GTO Pedders 160033 Xa Coilovers w/Mounts   +$1,197.00

Fixed Ratio Bound/Rebound Adjustable with Single Knob Adjustment

Included:
Front Upper Strut Mount Bearings
Front Sway Bar Links
Front Upper Strut Mounts
Rear Upper Shock Mounts

Front Spring Rate: 7 kg/mm
Rear Spring Rate: 8 kg/mm

 

1 x GTO Pedders 164033 Xa Supercar Coilovers w/ Remote Canisters w/Mounts   +$1,966.50

Independent Bound/Rebound Adjustable with Two Knob Adjustment

Included:
Front Upper Strut Mount Bearings
Front Swaybar Links
Front Upper Strut Mounts
Rear Upper Shock Mounts

 

Quantity 

Radius Rod Bushings (Forward)

• None Required

1 x GTO EP9166 Radius Rod Bushings - Forward   +$171.00

• The #1 GTO Suspension Failure is OEM Radius Arm Bushings
• Caster Adjustable using Included Shims
• Forward Washer Cupped for Better Performance
• Comes with Forward Center Nyloc Nuts
• Hardened Crush Tubes
• Helps Correct Inner Edge Tire Wear & Cupping Issues

 

Quantity 

Radius Rod Bushings (Rearward) - * Required

1 x GTO EP9019 Front Radius to Arm Bushings - Rearward   +$42.75

• Connects the Rear of the Radius Arm to the Lower Control Arm
• 2 Piece Bushings for Easy Installation
• Rear Nut Wrench Size is 30mm

 

Front Lower Control Arm Bushings - * Required

1 x GTO EP6500 Front Lower Arm Bushings   +$38.00

• Front Inner Control Arm to Frame
• Use with 6500-HK Hardened Bolt Kit
• 1 Package Per Car
• Increased Road Feel and Stability

 

Steering Rack Bushing - * Required

1 x GTO EP2105 Steering Rack Bushing   +$25.65

• Installs on Passenger Side of Rack
• Replaces OEM Rubber Bushing
• Tightens the Feel of the Steering
• Installation Requires Removal of the Right Outer Tie Rod

 

HD Radius Arms with New Nuts

2 x GTO 5409 Front HD Radius Arm   +$144.40

• Stronger than OEM
• Replace in Pairs
• Comes with Forward Center Nyloc Nuts
• Priced Per Arm (2 Required)

 

Rear Sub Frame Bushings - * Required

1 x GTO EP1145 Cradle/Subframe Bushings (New Design)   +$94.05

• Direct OE Fitment
• Hardened Crush Tubes
• Double Helix Internals
• High Durability
• New Design 2/2018 for Improved Performance
• Replace Bolts with our 48482-HK Hardened Bolts

 

Rear Lower Control Arm Bushings (Outer Position) - * Required

1 x GTO EP7023 Rear Lower Arm Bushings   +$46.55

• Non Adjustable Rear LCA Bushings
• 1 Kit Fits Either Inner or Outer Positions
• 2 Kits Fits Both Inner and Outer Positions
• 2 Piece Bushings for Easy Installation
• Adjustable Version (#5403) Also Available for Outer Position Only
• Use with 47937-HK Hardened Bolt Kit (1 Hardware Kit Per Bushing Kit)

 

1 x GTO 5403 Adjustable Rear Lower Arm Bushings   +$102.60

• Allows for Some Camber Adjustment
• Installs in to Outer Position Only
• Non Adjustable Version (#EP7023) Available
• Must be Tightened Very Tight After Alignment

 

Quantity 

Rear Lower Control Arm Bushings (Inner Position) Pedders Not Available - * Required

1 x GTO EP7023 Rear Lower Arm Bushings   +$46.55

• Non Adjustable Rear LCA Bushings
• 1 Kit Fits Either Inner or Outer Positions
• 2 Kits Fits Both Inner and Outer Positions
• 2 Piece Bushings for Easy Installation
• Adjustable Version (#5403) Also Available for Outer Position Only
• Use with 47937-HK Hardened Bolt Kit (1 Hardware Kit Per Bushing Kit)

 

Rear Diff Bushing Insert - * Required

1 x GTO EP1157 Diff Bushing Insert   +$42.75

• PolyUrethane Insert - Pushes in to the OEM Rubber Mount
• Helps make the rear suspension more effective
• Decreases the movement of the Rear Cradle
• Use in conjunction with EP1145 Subframe Bushings for Best Results
• Replace the Hardware with the 48390-HK Bolt Kit
• Some additional Driveline Noise may be heard

 

Front Swaybar - * Required

1 x GTO Front 30mm Adjustable Swaybar - 428005-30   +$230.85

GTO Front 30mm Adjustable Swaybar
Includes Poly D Bushings

 

Rear Swaybar - * Required

1 x GTO Rear 19mm Adjustable Swaybar - 429005-20   +$188.10

2 Adjustment Holes
Comes with Pedders D Bushings
19mm Diameter

 

Rear Swaybar End Link Bushings - * Required

1 x GTO Rear Swaybar Link Bushings - EP513   +$35.15

Replaces the Bushings in the OE Rear Links
Comes with new Ferrules

 

Tie Rods & Ball Joints etc.

1 x GTO Front Adjustable Swaybar Links for Pedders and BC Coilovers   +$142.50

GTO Front Adj Swaybar Links (Not for OE Style Struts)
Fits Pedders Xa Coilovers, and BC BR Coilovers.

 

2 x GTO Front Outer Tie Rod - PTE3049   +$58.90

Non KYB Rack Only - 16mm x 2.0 Threads
Fits 2004-2006 GTO up to VIN#  #########6L838608

 

2 x GTO PBJ8036 Front Lower Balljoint   +$85.50

GTO PBJ8036 Lower Balljoint

 

1 x GTO Front 401005L Hub Bearing - Left   +$153.90

GTO F 401005L Hub Bearing - L

 

1 x GTO Front 401005R Hub Bearing - Right   +$153.90

GTO F 401005R Hub Bearing - R

 

Hardware - * Required

1 x GTO 14432-HK Front Radius Arm Bushing Nut Hardware Kit (Replaces 11094432 x8)   +$8.55

• Includes 8 Small Lock Nuts
• These are the nuts that hold the Forward Radius Bushing to the Subframe

 

1 x GTO 14596-HK Front Swaybar Frame Bracket Hardware Kit (Replaces 11514596 x4)   +$7.60

Includes 4 Locking Nuts

 

1 x GTO 16363-HK Front Radius Arm Bushing Nut Hardware Kit (Replaces 11076363 x2)   +$6.65

• Includes 2 Lock Nuts
• This is the Large Center Nut that holds the Radius Arm to the Forward Radius Bushing
• 24mm Hex Size
• Included with Pedders EP9166 Radius Arm Bushings and 5409 Radius Arms

 

1 x GTO 18238-HK Front Lower Control Arm Hardware Kit (Replaces 92078238 x2/92138178 x2)   +$13.30

• Replaces the OEM Lower Control Arm Bolts/Nuts
• Fits Both Front Control Arms
• Upgraded from Black Oxide to Yellow Zinc

 

1 x GTO 19298-HK Radius Arm Forward Washers at Arm (Pair) (Replaces 90079298 x2)   +$28.50

Rearward at the Control Arm,  Goes in front of the control arm bushing between the Radius Arm.

Note: Washer Cups Away from Bushing

 

1 x GTO/G8 20981-HK Front Strut Mount Jam Nuts (Replaces 11010981 x2)   +$9.50

• Located Above the Upper Strut Mount
• Below the Retaining Plate
• Contains 2 Jam Nuts, One for Each Side

 

1 x GTO 28755-HK Front Camber Adjuster Bolt Hardware Kit (Per Pair) (Replaces 92138755 x2)   +$17.10

• Used for Adjusting Camber for Alignments
• MUST USE BLUE LOCTITE
• Replaces the Worn/Rotted OEM Adjusting Bolts

 

1 x GTO/G8 28863-HK Front Lower Strut Mounting Bolt Hardware Kit (Per Set of 4)   +$28.50

• Replaces 92138863 x 4, 11090821 x 4, 92138205 x 4, 92138049 x 4
• Replace with Struts or Coilovers
• Replacement Recommended After Loosening/Tightening a Number of Times
• Includes 4 Hardened Bolts, 4 Hardened Washers and 4 Hardened Locking Nuts
• Upgraded from Black Oxide to Yellow Zinc

 

1 x GTO/G8 28740-HK Front Strut Lock Nuts (Per Pair) (Replaces 92138740 x2)   +$24.70 Quantity 

• Above the Strut Retaining Plate
• Contains 2 Lock Nuts, One for Each Side

 

1 x GTO 31164-HK Steering Rack O-Rings - Lines to Rack (Pair)   +$7.60

• Includes 2 O-Rings for the Lines at the Rack
• Replace when the Lines are disconnected

 

1 x GTO 32963-HK Front Caliper Bolt Hardware Kit - 2004 Only (Replaces 92138557/92172963 x4)   +$19.00 Quantity 

• Bolts that Hold the Caliper Bracket to the Knuckle
• Includes 4 Hardened 10.9 Bolts
• Fits 2004 GTO Only
• Upgraded to Yellow Zinc

 

1 x GTO 35953-HK Steering Rack Mount Bolt Kit (Optional Fit: Rear Toe Link) (Replaces 11015953 x2/11092741 x2)   +$13.30

• Primary Fitment: Secures the Steering Rack to the Subframe
  (Replaces 11015953 x2/11092741 x2)
• Optional Fitment: Secures Rear Toe Link to Rear Subframe
  (Replaces 90468842 x 2 / 92228333 x 2)
• Contains two 10.9 Grade Bolts w/Nuts

 

1 x GTO 38238-HK Front Caliper Bolt Hardware Kit - 05-06 (Replaces 11518238 x4/92138897 x4)   +$34.20

• Bolts that Hold the Caliper Bracket to the Knuckle
• Includes 4 Hardened 10.9 Bolts with Nord-Lock Washers
• Fits 2005-2006 GTO Only
• Upgraded from Black Oxide to Yellow Zinc

 

1 x GTO 38396-HK Front Subframe Bolt Kit (4 Bolts) (Replaces 92138605 x2/92138396 x2)   +$95.00

• Secures Front Sub-Frame/Cradle to the Unibody
• UPDATED: Contains All 4 10.9 Grade Subframe Bolts
• Use in the Forward Location to Allow Cradle Alignment
• Use in the Rearward Location as Replacement Bolts
• Requires Thread Sealant/Locker

 

1 x GTO 45984-HK Rear Sway Bar Link 10.9 Bolt Kit (Both Sides)   +$13.30

• Replace OEM Hardware when Installing Swaybars, or Link Bushings
• 4x 10.9 Hardened Bolts
• 4x 10.9 Hardened Nyloc Nuts
• 4x Upper Washers - (Smaller - Outer / Larger - Inner Between Bar & Bushing)
• Stock Hardware will Break with Aftermarket Swaybars

 

1 x GTO 46304-HK Rear Lower Shock Bolt Hardware Kit (Replaces 92036304 x2/92078237 x2)   +$26.60

• Includes 2 Hardened Bolts, Washers and Lock Nuts
• Bolt is Longer to Allow Use of Nut
• Nut Allows Tightening when Control Arm Threads Strip out, as well as Added Strength

 

2 x GTO 47937-HK Rear Lower Control Arm Hardware Kit (Replaces 90447937 x2/92138178 x2)   +$38.00 Quantity 

• Replaces the OEM Lower Control Arm Bolts/Nuts
• Fits Rear Control Arms
• Rear Fitment is for Non Adjustable Bushings Only
• Rear Inner Requires 1 Kit (Non Adjustable Bushings)
• Rear Outer Requires 1 Kit (Non Adjustable Bushings)
• Upgraded from Black Oxide to Yellow Zinc

 

1 x GTO 48270-HK Rear Subframe Mount Bracket Bolt Kit (Set of 6) (Replaces 92138270 x6)   +$19.00

• Replaces OEM Bolts
• Includes 6 Bolts
• Fits the 'Triangle Bracket' below the Rear Cradle Bushings
• Upgraded from Black Oxide to Yellow Zinc

 

1 x GTO 48390-HK Rear Differential Mount 10.9 Bolt Kit (Replaces 92138390 x4)   +$9.50

• Includes 4 x10.9 Hardened Bolts
• Replace with Differential Mount Bushing
• Can also be Used for the Engine Skid Plate
• Upgraded from Black Oxide to Yellow Zinc

 

1 x GTO 48482-HK Rear Subframe Bolt Hardware Kit (Per Pair) (Replaces 92038482 x2)   +$28.50

• Replace OEM 8.8 Bolts with these Improved 10.9 Bolts
• Integrated Washer Allows for Better Torquability
• Install with Blue Loctitie
• Re-Useable vs OEM Single Use Bolts

 

1 x GTO 48545-HK Rear Sway Bar Frame Bracket Bolt Kit (Replaces 92138545 x2)   +$9.50

• Replaces 92138545
• 2 Slightly Longer than OE Bolts for Easier Installation
• Bolts MAY bottom out slightly
• The GTO only needs 1 bolt per bracket, the other end clips in to the subframe

 

1 x GTO 50093.50-HK Rear Axle Shaft Bolt Kit - 50mm (Stock Axles Only) (Replaces 92180093 x24)   +$33.25

• Secures the Halfshafts to the Stubs
• Contains 24 12.9 Grade Allen Bolts
• Blue Threadlocker Recommended

 

1 x GTO 54012-HK Differential Mount to Carrier Bolt Kit (Replaces 11024012 x2)   +$14.25

These 2 bolts hold the Diff Mount to the Diff Carrier (Pumpkin). (Not the Differential Mount Bolts)

 

1 x GTO 58127-HK Rear Caliper (Replaces 92138387 x4) / Differential Carrier to Subframe Locking Bolt Kit (Replaces 92138127 x4)   +$47.50

• Fits Rear Caliper Brackets
• Fits Rear Diff to Subframe
• Wide Nordlock Locking Washer Included
• Very High Quality

 

1 x Permatex Medium Strength Threadlocker 6.0 ml Blue   +$9.50

• Locks and seals while preventing parts loosening due to vibration
• Protects threads from corrosion
• Ideal for all nut and bolt applications 1/4" to 3/4" (6mm to 20mm)
• Removable with hand tools for easy disassembly

 

* Required Fields